一种用于电气设备状态监测的新式FBG传感器北大核心CSCD

为了监测绕组变压器的静态应力场和发生短路等故障时的动态应力变化,设计了一种用于电气设备状态监测的新式FBG传感器。该传感器由聚醚醚酮材料封装的FBG构成,通过内部圆锥形空腔结构实现将轴向应力集中于FBG敏感位置。通过仿真对不同压力强度下传感器结构的应力场部分及形变趋势进行了计算与分析,论证了设计的合理性。实验分别对静态载荷和动态冲击进行测试,结果显示,在静态压载测试中,当100 N相似文献   

Techno-economic assessment of hydrogen refueling station: A case study in Croatia

Hydrogen refueling station (HRS) capacity and location depend on the users, which makes it difficult to select the most favorable option before potential users are actually identified. As in Croatia, at least for now, there are no hydrogen users, this study considers a wide range of HRS capacities and their different configurations. These include hydrogen production and charging station within one existing wind farm in Croatia or both nearby the users, the hydrogen production within the wind farm and the charging station nearby the users, while hydrogen is delivered to the station with a tube trailer, and configuration of hydrogen production within the wind farm with a mobile charging station in case of several users in different locations. Each HRS configuration is evaluated by the obtained levelized cost of hydrogen depending on the capital, and operation and maintenance costs within the HRS techno-economic analysis provided.     

超高分子量聚乙烯纤维增强中空蜂窝模压复合材料性能研究

为研制车船等壳体所用的轻质、高强复合板材,选用超高分子量聚乙烯(UHMWPE)短纤维纱,制备成单层经纬为120根/(10 cm)的平纹组织,采用多组经纱持续更替交织层的方法制成2L(1+0)型、4L(2+1)型、6L(3+2)型3种多层角联锁结构织物,采用扦插芯棒、模压成型方法制成菱形蜂窝状的热固性环氧树脂基中空板,并与2块真空吸液法制成的面板组成“三合一”复合板,同时测定了复合板材的结构特征及其平拉、平压和弯曲性能。结果表明:3种类型复合板的密度均远小于水的密度,其中6L(3+2)型最小,为0.48 g/cm³;复合板层数越多,环氧树脂越难渗透尤其是在中空板菱形交叉点处,复合板平拉、平压、抗弯曲强度则呈现递增,制成的6L(3+2)型复合板试样平压强度可达到1.03 MPa。     

Evaluation of back-calculated elastic moduli of unreinforced and geocell-reinforced unbound granular material from full-scale field tests

This paper presents a field-scale experimental track over a poor subgrade with an unreinforced section and a geocell-reinforced section subjected to in-situ performance tests. Plate load tests and Benkelman beam tests were carried out distributed in several unreinforced and reinforced layers. The objective was to: (1) examine the variability of the elastic modulus of unbound granular material (UGM) due the influence of its thickness and the presence of poor subgrade in its base, (2) evaluate the modulus improvement factor (MIF) generated by the geocell reinforcement in the UGM and (3) verify the most appropriate condition to apply the MIF to transport infrastructure design. The results showed that there is a significant influence of the thickness of the UGM layer on its elastic modulus when the layer is supported directly over a soft subgrade. The MIF values obtained in field suggest that its determination is mostly related to the UGM maximum elastic modulus rather than its decreased values (by virtue of poor subgrade or reduced thicknesses), and that the analytical formulation presented for MIF calculation has good predictive capability to be applied to pavement design.     

Finite element limit analysis of load-bearing performance of reinforced slopes using a non-associated flow rule

This paper presents a numerical study on the load-bearing performance of reinforced slopes under footing load using a finite element limit analysis (FELA) method where a non-associated flow rule is assumed in the analysis. The method was validated against results from full-scale model tests and a limit equilibrium (LE) analytical method. A series of parametric analyses was subsequently carried out to examine the influences that the soil dilation angle, footing location, and reinforcement design (i.e. length, tensile strength, and vertical spacing) could have on the load-bearing performance of reinforced slopes. Results indicate that dilation angle has a significant influence on the predicted magnitudes of bearing capacity, slope deformation, and mobilized reinforcement load. The predicted values of bearing capacity using the FELA are smaller than those from the Meyerhof's analytical method for unreinforced semi-infinite foundation, especially for larger friction angle values. Additionally, the ultimate bearing capacity of the slope and its corresponding horizontal deformation increase with the reinforcement tensile strength. Finally, the slip planes under the applied footing load are found to be y-shaped and primarily occur in the upper half of the slope.     

Fabrication of high-efficiency Yb:Y2O3 laser ceramics without photodarkening

High-efficiency Yb:Y₂O₃ laser ceramics were fabricated using the vacuum-sintering plus hot isostatic pressing (HIP) without sintering additives. High-purity well-dispersed nanocrystalline Yb:Y₂O₃ powder was synthesized using a modified co-precipitation method in-house. The green bodies were first vacuum sintered at a temperature as low as 1430°C and then HIPed at 1450°C. Finally, the samples were air annealed at 800°C for 10 h. Although no sintering aids were used, full density of the samples with excellent optical homogeneity and an inline transmission of 80% at 400 nm could be obtained. Moreover, photodarkening phenomenon was not detected in the ceramics. Preliminary laser experiment with the fabricated ceramics in a two-mirror cavity has demonstrated 32 W continuous-wave (CW) output at ∼1077 nm with an optical-to-optical conversion efficiency of 58.2%. To the best of our knowledge, this is so far the highest CW output power and optical-to-optical conversion efficiency achieved with the Yb³⁺-doped sesquioxide ceramics in a simple two-mirror cavity.     

Omega-6支撑身体，Omega-3支撑大脑：均衡摄入对儿童大脑发育的影响（网络首发、推荐阅读）

人体大脑和身体的发育，需要从食物中摄取均衡的营养物质。人类大脑是区分人类和其他动物的特征。食物中的必需脂肪酸是机体组织结构和功能的必要组成部分。Omega-6（O6）亚油酸（LA6）是皮肤组织的组成成分，且是炎症、血栓形成、免疫和其他信号分子的前体；Omega-3（O3）α-亚麻酸（ALA3），特别是其长链代谢产物——二十二碳六烯酸（DHA3），是大脑、视网膜和部分神经组织中的关键组分。从富含LA6脂肪酸（缺乏O3脂肪酸）的植物籽中提取出的廉价而优质油脂，是20世纪的西方国家食品工业生产的主要脂肪来源。在代谢通路中，高浓度的LA6脂肪酸可拮抗O3脂肪酸代谢，造成O3脂肪酸不足，因此，在给怀孕动物的饲料中，只提供富含LA6但缺乏O3脂肪酸的油脂作为唯一的脂肪来源，会导致幼崽大脑发育不良。过去20~30年的研究表明，低含量LA6且含DHA3的油脂可改善大脑的功能。近年来的研究较多集中在营养因素对大脑发育的影响，最新研究数据表明，脂肪酸平衡对营养不良儿童的大脑发育尤为重要。世界卫生组织（WHO）越来越重视大脑的营养健康，通过其下属的食品法典委员会，建议用于治疗严重急性营养不良儿童的即食治疗食品中，使用含有均衡脂肪酸组成/构成的脂肪。同样，脂肪酸均衡对老年人可能也很重要。目前，业界已经有了调整油脂成分的方法，以确保脂肪酸均衡，从而维持人体整个生命周期的大脑健康。     

超高效液相色谱⁃四极杆⁃飞行时间质谱对含PET食品接触材料中可迁移非挥发性物质的筛查研究

采用超高效液相色谱⁃四极杆⁃飞行时间高分辨质谱（UPLC⁃Q⁃TOF）对4类不同类型的含聚对苯二甲酸乙二醇酯（PET）材质的食品接触材料在4 %乙酸和50 %乙醇模拟物中的迁移出的非挥发性未知物进行筛查解析。结果表明，产品在4 %乙酸模拟物的迁移风险远小于50 %乙醇模拟物，主要迁移物质为聚合单体形成的寡聚物，抗氧剂、润滑剂、胶黏剂等加工助剂以及生产加工、迁移过程中形成的非有意添加物（NIAS）物质；纯PET材质的产品迁移物质较少，多层复合材料迁移物质较多。复合材质的产品中，PET材质可能在生产时添加了己二酸、癸二酸、新戊二醇等物质，进行了改性处理；此外，部分迁移物质会与模拟物中的乙醇发生反应，生成新的NIAS物质。     

Generation,validation and application of dynamic load profiles in flow measurement using cavitating Herschel–Venturi nozzles

Today, utility meters for water are tested for measurement behavior at stable operating conditions at specified flow rates as part of the approval process. The measurement error that occurs during start and stop or when changing between flow rates may not be taken into account. In addition, there are new technologies whose measuring behavior under real-world conditions is only known to a limited extend. To take these facts into account, a new method has been developed and tested to determine the measurement behavior of water meters under dynamic load profiles as they occur in the real application. For this purpose, a test rig for flow rate measurement was extended by a cavitation nozzle apparatus and the generation of dynamic load profiles was validated. For the cavitation nozzles used, possible factors influencing the flow rate, such as temperature and purity of the water as well as the upstream pressure were investigated. Using different types of domestic water meters, the applicability of the dynamic test procedure was demonstrated and the measurement behavior of the meters was characterised.     

Microstructural and mechanical properties assessment of transient liquid phase bonding of CoCuFeMnNi high entropy alloy

The transient liquid phase (TLP) bonding of CoCuFeMnNi high entropy alloy (HEA) was studied. The TLP bonding was performed using AWS BNi-2 interlayer at 1050 °C with the TLP bonding time of 20, 60, 180 and 240 min. The effect of bonding time on the joint microstructure was characterized by SEM and EDS. Microstructural results confirmed that complete isothermal solidification occurred approximately at 240 min of bonding time. For samples bonded at 20, 60 and 180 min, athermal solidification zone was formed in the bonding area which included Cr-rich boride and Mn₃Si intermetallic compound. For all samples, the γ solid solution was formed in the isothermal solidification zone of the bonding zone. To evaluate the effect of TLP bonding time on mechanical properties of joints, the shear strength and micro-hardness of joints were measured. The results indicated a decrement of micro-hardness in the bonding zone and an increment of micro-hardness in the adjacent zone of joints. The minimum and maximum values of shear strength were 100 and 180 MPa for joints with the bonding time of 20 and 240 min, respectively.